Polyurea spray coating for foundations, parkades, and below-grade spaces. One seamless, monolithic membrane, walk-on ready in minutes, with none of the lap seams that sheet membranes fail at. For repairs on existing structures and full scopes on new builds.
Fully insured · Engineer-spec systems · Owner on every job · Written warranty
Cracks are common after Edmonton winters, and small leaks grow fast. Polyurea spray bonds straight to the concrete, creating one seamless, permanent barrier with no lap seams to fail and no long shutdown.
We specialize in commercial waterproofing in Edmonton using polyurea spray coating. This rapid-cure, spray-applied system bonds directly to prepared concrete, creating a seamless, flexible membrane that permanently stops water infiltration in foundations, parking structures, warehouses, and below-grade spaces. We handle both repairs on existing buildings and full waterproofing scopes as part of new-construction teams.
Polyurea is one of the most durable waterproofing coatings available. It cures in seconds, flexes with over 400% elongation so it moves through freeze-thaw cycles without cracking, and becomes permanently hydrophobic once set. Because it’s spray-applied as one continuous layer, there are no lap seams for water to find — and it costs a fraction of digging out the foundation.
Polyurea spray applied directly to prepared foundation walls, forming a seamless, permanently hydrophobic barrier.
Edmonton’s climate and ground conditions make water infiltration close to universal. The usual causes:
Free on-site assessment — We inspect the structure, find every crack and water source, and provide a written scope with a fixed quote.
Surface preparation — Concrete is cleaned, degreased, and ground or shot-blasted to open the pores. Cracks and active leaks are stopped first. Prep is the single biggest factor in long-term adhesion.
Polyurea spray application — A two-component polyurea system is sprayed to the specified thickness. It reacts and cures in seconds into a seamless, monolithic coating. No joints, no seams, no gaps.
Cure & verification — Surfaces are walk-on ready within minutes. We inspect the membrane for pinholes, touch up as needed, and provide a written warranty.
Traditional waterproofing means digging out the foundation to apply membranes from outside. Polyurea spray gets you a seamless membrane without the dig, the downtime, or the landscaping bill.
Our commercial waterproofing clients include property managers, building engineers, general contractors, and facility directors across Edmonton — anyone responsible for maintaining or delivering a dry, code-compliant structure. Common scenarios we’re called for:
Engineers and general contractors increasingly spec polyurea spray coatings on new commercial construction. Where we fit in:
Polyurea spray waterproofing typically costs 50 to 70 percent less than traditional excavation-based waterproofing, which often runs $20,000 to $50,000 or more once digging, disposal, and landscaping repair are counted. There’s no excavation with spray coating, so the cost stays predictable. Every project gets a free assessment and a fixed written quote.
Prep is critical for adhesion. We clean, degrease, and grind or shot-blast the concrete, repair cracks and spalls, stop any active leaks, and prime. Proper preparation is what decides whether the membrane lasts decades or fails early, so we don’t cut corners on it.
Installed properly on a prepared surface, it’s a permanent-grade barrier. The cured membrane flexes with over 400% elongation, so it moves through Edmonton’s freeze-thaw cycles without cracking, and it stays permanently hydrophobic, chemical-resistant, and abrasion-resistant.
Very little. Polyurea cures in seconds to minutes, so most coated surfaces are walk-on ready within an hour. Surface prep is the longest phase, but there’s no excavation, no heavy equipment, and no long cure wait. We can phase the work around your hours.
Yes, that’s one of our most common commercial jobs. We seal deck cracks, expansion joints, drain areas, column bases, and ramps, all high-risk spots where salt and traffic drive water into the structure.
Yes. We spec the correct polyurea system with structural engineers and architects, and provide SDS sheets, technical data sheets, and certifications on request, plus scope reports, before-and-after photos, and written warranties for your files.
Serving Edmonton and commercial sites across Alberta
Licensed and insured to work anywhere in Alberta.
